﻿FACTORY: THE INDUSTRIAL DEVOLUTION
'Becca's Month Construction Hints



Part A:  Creating a palette of components (the following advice applies only to the graphics program that comes with Factory):

1. Draw the finished product first, before you start the components, so that you will know for sure that the finished product will fit within the available frame. Then, draw the pieces that make up the product to the same scale.

2. If you can, try to leave at least one square in the palette white (select that square as if you were going to draw something, but just click on okay), so you can use that square as an eraser when you add background images to the layout that you decide you don't want. Then, when you create the layout and screw up the background, you can remove the background mistake without disturbing the foreground.

3. It's best if you outline each component in black -- if one dot/bit is missing from the outline, or if it is not all black, sometimes the components become invisible (this applies to the waste you draw, too). When you are testing a work day, if you hear objects drop but don't see anything, or presses mysteriously start running, that is the problem.

4. If you run into unidentifiable problems when testing a day, one of the most likely causes is that you didn't set up the 'combinations' right. Go through each component, making sure they are set up right and that any other junk Factory automatically set there is cleared (press the 'Clear' button to make the square gray). If you make changes to the layout (like you decide a different press should spray the chocolate than the one you originally chose), remember to go back and update the 'combinations' in that workday's palette.

5.  When you are done drawing a component, select and drag it as far to the bottom of the frame as you can (without cutting part of the image off) and center it. This will make the image line up properly with pipes, etc.

6. Take the time to draw nice graphics. Round objects take time, three-dimensional objects take time, different colors take time. Your fans will thank you for it. Creating shadows with different levels of gray is nice.

Mercedonius has exceptional graphics. Go take a look at how they have been constructed.

7.  To make an object see-through, remove one dot/bit from outline. It may make the image look crappy, but sometimes it isn't that noticeable.



Part B:  Creating a layout

1. Pay close attention to whether you have selected "Pipes" or "Background Pipes"! There are many differences. If you meant to select pipes and choose background pipes, you will be able to see the objects fall through pipes, which looks weird. Also, background pipes can be removed without disturbing the foreground by using the white square you set aside as an eraser (see A2, above), and regular pipes (and anything else) can be cleared from the foreground by holding down the shift key while clicking on the square.

2. In my opinion it is much faster and easier to create a layout from scratch (select 'clear layout') than to modify one to suit your needs. (Likewise for the assembly guide).

3. There are many different ways to set up your layout. On the one hand there are some rules that can never be broken (there must be one clock, a conveyor belt can't go in two directions), but there is lots that you can fiddle with to get a different look. Look carefully at the months others have created, so you know all your options.

4. I think it's better to have the truck visible in your layout, rather than a pipe going down to the truck, unless it's unavoidable. It looks nicer, since you can see the completed product on the side of the truck.

5. Try to learn the numbers on the different component menus in the layout mode as soon as possible. This will make your life much easier, so you don't have to click 18 times to find the pipes you want.



Part C:  Other hints

1. Make sure you set the difficulty level, the quota, and the degree of rationality of the inputs (random/crazy/insane, etc.) to a reasonable level.

The only thing you will accomplish by setting them too high is that you will royally piss off the people you want to be enjoying your month. For example, setting a quota of 30 on a monotonous product is not funny, it's annoying as hell. So is getting 356 MiracleBras in a row before you get a hangar to put them on. The best way to make a game difficult is by:  1. having lots of components; and  2. making your layout tough -- requiring that components be passed through presses more than once, not giving them any storage tanks, giving them a trash pipe just before but not after the final press, etc.

2. Make sure you test every workday for glitches -- common ones are forgetting to tell Factory that the finished product is in fact the finished product (by clicking on the square over the product name when you first enter edit mode), typos in the text, and verbal directions or assembly guides which don't match the layout.

3.  If you distribute your month without password protection, we'll love you even more.



The above comments are my own subjective opinion. Follow your own instincts. Good luck!


